Interior paints, decorative plasters and textured coatings for painting walls, ceilings, partitions and other indoor surfaces.
PAINTS AND COATINGS FOR INTERIOR WORK
A wide range of products to bring your ideas to life
Materials for rooms with normal and high humidity
Tinting in thousands of colors according to RAL, NCS and other color catalogs
Conceals minor wall defects
Easy and convenient to apply
Does not require a perfectly smooth prepared surface
Creates a durable textured coating
Praktik decorative paint "Shagreen"
Packaging:
Water-dispersion textured paint for interior work
Download specifications
Purpose:
Paint for decorative finishing and providing surface relief inside dry rooms with moderate humidity.
Substrate type:
Consumption:
1.5−1.8 kg/m²
Gloss level:
Matte
Tinting:
The paint can be tinted in accordance with NCS, RAL, and other tinting systems.
Paint for decorative finishing and providing surface relief inside dry rooms with moderate humidity.
Substrate type:
- For concrete, brick, previously filled or plastered surfaces, and gypsum plasterboard panels.
- Also used for finishing previously painted surfaces with water-dispersion paints that are firmly adhered (after preliminary sanding).
- Brush
- Roller
- Spray gun
Consumption:
1.5−1.8 kg/m²
Gloss level:
Matte
Tinting:
The paint can be tinted in accordance with NCS, RAL, and other tinting systems.
Composition:
Copolymer dispersion, fillers, thickeners, functional additives, water.
Color:
White
Gloss level:
Matte
Washability:
Cleaning with a dry non-abrasive sponge or a soft-bristled brush.
Density:
1.7–1.8 kg/l
Non-volatile matter content:
approx. 78%
Consumption* per 1 coat:
1.5-1.8 kg/m²
Thinner:
Water
Coverage*:
From 1–1.5 m²/kg
Drying time**:
up to 24 hours.
Substrate temperature during application:
from +5 °C to +35 °C
* Material consumption depends on the quality of substrate preparation, application method, tools used, and the skill of the workers, and may differ from the specified values.
** At t (+20±2) °C and relative air humidity not exceeding (65±5) %. Drying time may increase if the temperature decreases or humidity increases.
Copolymer dispersion, fillers, thickeners, functional additives, water.
Color:
White
Gloss level:
Matte
Washability:
Cleaning with a dry non-abrasive sponge or a soft-bristled brush.
Density:
1.7–1.8 kg/l
Non-volatile matter content:
approx. 78%
Consumption* per 1 coat:
1.5-1.8 kg/m²
Thinner:
Water
Coverage*:
From 1–1.5 m²/kg
Drying time**:
up to 24 hours.
Substrate temperature during application:
from +5 °C to +35 °C
* Material consumption depends on the quality of substrate preparation, application method, tools used, and the skill of the workers, and may differ from the specified values.
** At t (+20±2) °C and relative air humidity not exceeding (65±5) %. Drying time may increase if the temperature decreases or humidity increases.
Scope of application
Suitable for concrete, brick, previously filled or plastered surfaces, and gypsum plasterboards.
Also used for finishing previously painted surfaces with water-dispersion paints that are firmly adhered (after preliminary sanding).
For use in common areas (inter-apartment corridors, stairwells, halls, and lobbies). Recommended for residential, commercial, industrial, and warehouse premises.
Suitable for manual and machine application.
Permitted for use in buildings and structures of types:
Suitable for concrete, brick, previously filled or plastered surfaces, and gypsum plasterboards.
Also used for finishing previously painted surfaces with water-dispersion paints that are firmly adhered (after preliminary sanding).
For use in common areas (inter-apartment corridors, stairwells, halls, and lobbies). Recommended for residential, commercial, industrial, and warehouse premises.
Suitable for manual and machine application.
Permitted for use in buildings and structures of types:
- Type A — residential buildings and dormitories; buildings and premises of organizations for the upbringing and education, recreation and health improvement of children and youth; healthcare organizations; homes for the disabled and elderly; sanatoriums; rest homes; indoor sports facilities; office premises with permanent occupancy in administrative buildings at industrial enterprises and other objects of types B, V.
- Type B — food industry, trade, and public catering enterprises; hotels; non-food stores; communication enterprises; consumer service enterprises; cultural and entertainment facilities and other objects; administrative buildings.
- Type V — industrial enterprises, auxiliary and utility rooms and structures; warehouses; garages
Paint tinting can be carried out in accordance with NCS, RAL, and other tinting systems; it is permissible to add up to 5% of tinting pastes by weight of the paint.
To avoid differences in shade on the same surface, use a product with the same batch number (see on the package) or pre-mix materials from different batches in a 1:1 ratio. The organization performing the tinting is responsible for the tinting result.
Depending on the application conditions, as well as the texture of the painted surface, actual color shades may differ slightly from those presented in the color catalog. Before application, it is necessary to perform a test application and check the dried coating for compliance with the color.
After adding tinting pastes, the product should be used as soon as possible to avoid changes in the properties of the tinted material during storage.
To avoid differences in shade on the same surface, use a product with the same batch number (see on the package) or pre-mix materials from different batches in a 1:1 ratio. The organization performing the tinting is responsible for the tinting result.
Depending on the application conditions, as well as the texture of the painted surface, actual color shades may differ slightly from those presented in the color catalog. Before application, it is necessary to perform a test application and check the dried coating for compliance with the color.
After adding tinting pastes, the product should be used as soon as possible to avoid changes in the properties of the tinted material during storage.
Surface Preparation
Surface preparation should be carried out in accordance with SP 71.13330.2017. Clean the substrate of dust and dirt. Remove unstable layers of old paint and whitewash from previously painted surfaces. Sand hard and firmly adhering glossy surfaces to a matte state, and remove the sanding dust.
Level irregularities, depressions, cracks, and chips with water-dispersion putty and sand them down. Surfaces previously covered with chalk or lime paints must be thoroughly cleaned until completely removed.
Intensively absorbing surfaces should be pre-primed to increase the reliability of the coating and reduce paint consumption. For manual application, to improve adhesion to low-absorbent and smooth mineral substrates, it is recommended to use Bergauf Facade Grunt adhesive primer.
It is recommended to use primers from the Praktik line (depending on the type of substrate), as well as putties.
Application Procedure
The surface to be painted must be dry and clean. The temperature of the substrate and the environment for paint application should be from +5 °C to +35 °C, relative air humidity (65±5) %. During work, avoid exposure to direct sunlight, high humidity conditions, and atmospheric precipitation.
Mix the paint thoroughly before use. To avoid differences in shade on the same surface, use a product with the same batch number (see on the package) or pre-mix materials from different batches in a 1:1 ratio.
Depending on the application conditions, as well as the texture of the painted surface, actual color shades may differ slightly from the reference ones. Before application, it is necessary to perform a test application and check the dried coating for compliance with the desired color.
Application Technology
Apply the paint with a brush, roller, or hopper gun in 1 layer on the prepared surface. Parameters for spray application: for paint with a grain size of 0.5 mm — 1.0 mm, pressure 3 atm, nozzle diameter 4 mm. More precise parameters are determined by test painting at the site.
Surface preparation should be carried out in accordance with SP 71.13330.2017. Clean the substrate of dust and dirt. Remove unstable layers of old paint and whitewash from previously painted surfaces. Sand hard and firmly adhering glossy surfaces to a matte state, and remove the sanding dust.
Level irregularities, depressions, cracks, and chips with water-dispersion putty and sand them down. Surfaces previously covered with chalk or lime paints must be thoroughly cleaned until completely removed.
Intensively absorbing surfaces should be pre-primed to increase the reliability of the coating and reduce paint consumption. For manual application, to improve adhesion to low-absorbent and smooth mineral substrates, it is recommended to use Bergauf Facade Grunt adhesive primer.
It is recommended to use primers from the Praktik line (depending on the type of substrate), as well as putties.
Application Procedure
The surface to be painted must be dry and clean. The temperature of the substrate and the environment for paint application should be from +5 °C to +35 °C, relative air humidity (65±5) %. During work, avoid exposure to direct sunlight, high humidity conditions, and atmospheric precipitation.
Mix the paint thoroughly before use. To avoid differences in shade on the same surface, use a product with the same batch number (see on the package) or pre-mix materials from different batches in a 1:1 ratio.
Depending on the application conditions, as well as the texture of the painted surface, actual color shades may differ slightly from the reference ones. Before application, it is necessary to perform a test application and check the dried coating for compliance with the desired color.
Application Technology
Apply the paint with a brush, roller, or hopper gun in 1 layer on the prepared surface. Parameters for spray application: for paint with a grain size of 0.5 mm — 1.0 mm, pressure 3 atm, nozzle diameter 4 mm. More precise parameters are determined by test painting at the site.
Storage and Transportation Conditions
Store and transport in tightly closed containers at a temperature of at least +5° and no more than +35°C. Five-fold freezing is allowed for a total duration of no more than 2 weeks at a temperature not lower than -40°C.
The bucket with the product should be protected from excessive heating and avoid storage under direct sunlight. Subject to the conditions, the guaranteed shelf life in closed factory packaging is 12 months from the date of manufacture.
During storage, product separation is possible, which is easily eliminated by stirring. Keep partially used product in tightly closed containers and use as soon as possible.
Safety
The product is fire- and explosion-proof, does not contain flammable components.
Store and transport in tightly closed containers at a temperature of at least +5° and no more than +35°C. Five-fold freezing is allowed for a total duration of no more than 2 weeks at a temperature not lower than -40°C.
The bucket with the product should be protected from excessive heating and avoid storage under direct sunlight. Subject to the conditions, the guaranteed shelf life in closed factory packaging is 12 months from the date of manufacture.
During storage, product separation is possible, which is easily eliminated by stirring. Keep partially used product in tightly closed containers and use as soon as possible.
Safety
The product is fire- and explosion-proof, does not contain flammable components.