Purpose:
The paint is intended for painting mineral facades of residential and administrative buildings, as well as for walls and ceilings in rooms with normal and high humidity. It creates a coating resistant to atmospheric precipitation and biological damage.

Substrate type:
The paint can be applied to new and previously water-dispersion painted mineral surfaces, plastered, puttied, concrete, brick, asbestos-cement surfaces, as well as gypsum board, fiberboard, and particleboard exposed to atmospheric influences or used indoors. Do not use on surfaces painted with lime silicate paints and organic elastic coatings.

Application method:

• Brush
• Roller
• Spray gun

Consumption:
8−11 m²/l

Gloss level:
Matte

Tinting:
The paint is produced in two bases, A and C, and can be tinted using computer (machine) methods into RAL, NCS, and other color catalogs.

Composition:
Polymer dispersion, pigments, fillers, functional additives, biocides, water.

Color:
Base A — white. Base C — transparent

Base:
A/C

Gloss level:
Matte

Consumption per 1 coat on non-absorbent surface:
8−11 m²/kg*

Density:
Base A 1.5−1.55 kg/l
Base C 1.35−1.4 kg/l

Touch dry time:
1 hour**

Next coat can be applied after:
1 hour**

Wash resistance:
Washing with non-abrasive detergents, no earlier than 2 weeks after application

Water absorption GOST 33352:
less than 0.1 kg/(m2*h0.5), class W3

Vapor permeability resistance GOST 25898:
less than 0.15 m2*h*Pa/mg

Substrate temperature during application:
From +5 to +35ºC

*Material consumption depends on the quality of preparation and the absorption capacity of the substrate, the application method, the tool used, the qualification of the workers, and may differ from the specified values.
** At t (+20±2)°C and relative air humidity of no more than (65±5)%. When the temperature decreases or humidity increases, the drying time may increase. At air temperatures below +15℃ or relative air humidity above 65%, apply the next coat no earlier than after 24 hours.

The paint is intended for painting the facades of residential and administrative buildings. The paint can be applied to surfaces made of brick, concrete, asbestos cement, plastered and previously painted surfaces exposed to atmospheric influences, as well as those used indoors to obtain coatings resistant to wet cleaning and washing.

The paint can be applied to concrete, brick, fiberboard and particleboard, gypsum plasterboard, plastered, and previously painted surfaces (but not glossy ones). Not recommended for painting plinths.
For manual and mechanized application.

The paint is produced in two bases: A (pastel colors) and C (saturated colors) and can be tinted by computer (machine) method into RAL, NCS and other color catalogs. Manual tinting using water-based tinting pastes is possible. Base A can be used as white paint, base C is used only in tinted form.
The organization performing the tinting is responsible for the tinting result.

Depending on the application conditions, as well as the texture of the surface being painted, the actual color shades may slightly differ from those presented in the color catalog.
Before application, it is necessary to perform a test application and check the dried coating for color compliance.
After adding tinting pastes, the product should be used as soon as possible to avoid changes in the properties of the tinted material during storage.

To avoid differences in shade, it is recommended to use product from the same production batch on one visual plane (the batch number is indicated on each package) or to pre-mix materials from different batches in a 1:1 ratio; the application technology must remain unchanged.

SUBSTRATE PREPARATION
Substrate preparation should be carried out in accordance with SP 71.13330.2017.
Clean the substrate from dust and dirt. Remove unstable layers of old paint and whitewash from previously painted surfaces. Sand hard and firmly adhering glossy surfaces to a matte state, and remove the sanding dust. Level unevenness, depressions, cracks, and chips with Bergauf putty, Bergauf, sand down.
Surfaces previously covered with chalk or lime paints must be thoroughly cleaned until completely removed. Highly absorbent surfaces should be pre-primed with Praktik strengthening primer for painting to increase coating reliability and reduce paint consumption.

WORK PROCEDURE
Stir the paint thoroughly. The paint is ready for use; if necessary, dilution with water of no more than 5% is possible. Apply the paint to a prepared dry clean surface with a roller, brush, or spray gun. For rough surfaces (textured plasters, brick, concrete blocks, relief ceilings), it is recommended to use rollers with a pile length of 12–25 mm. For coarse surfaces (putties, plasters, concrete) — with a pile length of 8–12 mm. For smooth surfaces (drywall, MDF, particle board, architectural decor elements (casings, moldings, ceiling cornices)) — with a pile length of up to 6 mm. For airless spraying, dilution with water by 5–10% is allowed, nozzle 0.013–0.015″, pressure 180–190 bar. During work, avoid exposure to direct sunlight, high humidity conditions, and atmospheric precipitation. Air and substrate temperature during application from +5°C to +35°C, relative air humidity below 80%.
To obtain a rich color and improve the appearance of the surface, it is necessary to apply two coats of paint. To avoid differences in shade, use paint from the same batch. It is recommended not to take breaks when painting a continuous surface; work using the "wet-on-wet" method at "overlap" points. Work should be finished at architectural boundaries (at the corners of the building, under downspouts, etc.).
After completing the work, wash hands and tools thoroughly with warm water.

SAFETY PRECAUTIONS
Work should be performed using personal protective equipment for hands, eyes, and respiratory tract. Use in well-ventilated areas. In case of contact with eyes, rinse immediately with water. In case of contact with skin, wash with soap and water.

STORAGE AND TRANSPORTATION
Store and transport in tightly closed containers at temperatures from +5°C to +35°C. Five-fold freezing for a total duration of no more than 2 weeks at a temperature not lower than -40°C is allowed. The product bucket should be protected from excessive heating and storage under direct sunlight should be avoided. Subject to storage conditions, the guaranteed shelf life in closed factory packaging is 24 months from the date of manufacture. During storage, product separation may occur, which is easily eliminated by stirring. Keep partially used product in a tightly closed container and use as soon as possible.
The product is fire and explosion safe, and does not contain flammable components.

DISPOSAL
Do not pour paint products into sewers, water bodies, or onto the soil. Dispose of dry empty containers in accordance with local legislation; transfer liquid residues to hazardous waste collection points.