Purpose:
Paint for kitchens and bathrooms.

Substrate type:

• New and previously painted with water-dispersion paints walls and ceilings
• Plastered, puttied surfaces
• Concrete
• Brick
• Gypsum board
• Chipboard and fiberboard

Application method:

• Brush
• Roller
• Spray gun

Consumption:
7-12 m²/l

Gloss level:
Semi-matte (10-12%)

Tinting:
The paint is produced in two bases, A (white) and C (transparent). It can be tinted manually or by computer (machine) method into RAL, NCS, and other color catalogs.

Composition:
Polymer dispersion, pigments, fillers, functional additives, water.

Color:
Base A — white; Base C — transparent

Gloss level:
Semi-matte (10−12%)

Consumption per 1 coat on a smooth non-absorbent surface:
9−12 m²/l*

Consumption per 1 coat on an uneven absorbent surface:
7−9 m²/l*

Drying time:
1 hour**

Next coat can be applied after:
2 hours**

Wash resistance:
Repeated wet cleaning with detergents.

Wet scrub resistance GOST 32300/ DIN EN 13300:
Class 1

Substrate temperature during application:
+5 °C to 35 °C

Shelf life:
24 months

* Material consumption depends on the quality of substrate preparation, application method, tools used, and the skill of the workers, and may differ from the specified values.
** At t (+20±2)°C and relative air humidity not exceeding (65±5)%. When the temperature decreases or humidity increases, the drying time may increase. At air temperatures below +15°C or relative air humidity above 65%, apply the next coat no earlier than after 24 hours.

Silky-matte high-opacity water-dispersion paint, exceptionally resistant to washing and abrasion, resistant to condensation, and prevents mold growth.

Designed for finishing surfaces inside dry and humid rooms subject to high operational loads (kitchens, bathrooms, dining rooms, laundries, corridors, etc.), as well as rooms with requirements for frequent wet cleaning, including the use of detergents and disinfectants. Resistant to household stains.
Eco-friendly and hypoallergenic.

Applied to new and previously water-dispersion painted walls and ceilings, on plastered, puttied, concrete, brick surfaces, gypsum board, particle board, and fiberboard.
For manual and machine application.

Approved for use in buildings and structures of the following types:
Type A — residential buildings and dormitories; buildings and premises of educational, training, recreation, and health organizations for children and youth; healthcare organizations; nursing homes and homes for the disabled; sanatoriums; rest homes; indoor sports facilities; office premises with permanent human presence in administrative buildings at industrial enterprises and other objects of types B, C.
Type B — food industry, trade, and catering enterprises; hotels; non-food stores; communication enterprises; consumer service enterprises; cultural and entertainment facilities; administrative buildings.
Type C — industrial enterprises, auxiliary and utility rooms and structures; warehouses; garages.

The paint is produced in two bases, A and C, and can be tinted by computer (machine) method into RAL, NCS, and other color catalogs. Base A is intended for tinting into light and pastel shades and can also be used as white paint; it is permissible to add up to 5% tinting pastes by weight of the paint.
Base C is used only in tinted form and is intended for tinting into saturated shades; it is permissible to add up to 10% tinting pastes by weight of the paint. When painting in bright colors using Base C, it is recommended to first apply a coat of Base A paint tinted to a similar shade. Manual tinting using water-based tinting pastes is possible.
The organization performing the tinting is responsible for the result. Depending on the application conditions and the texture of the surface being painted, actual shades may differ slightly from those presented in the color catalog.
Before application, a test application must be performed to check the dried coating for color compliance.
To avoid differences in shade, it is recommended to use product from the same production batch on one visual plane (the batch number is indicated on each package) or pre-mix materials from different batches in a 1:1 ratio; the application technology must remain unchanged.

Surface preparation:

Substrate preparation should be carried out in accordance with SP 71.13330.2017.

• Clean the substrate from dust and dirt. Remove unstable layers of old paint and whitewash from previously painted surfaces.
• Hard and firmly adhering glossy surfaces should be sanded to a matte state, and sanding dust must be removed.
• Level out irregularities, depressions, cracks, and chips with Bergauf UNI PASTA water-dispersion putty, then sand.
• Surfaces previously covered with chalk or lime paints must be thoroughly cleaned until completely removed. Intensively absorbing surfaces should be pre-primed with Bergauf Techno Primer deep penetration primer to increase coating reliability and reduce paint consumption.

The surface to be painted must be dry and clean; the substrate temperature for the work must be at least +10°C, the room temperature during paint application must be between +10°C and +35°C, and the relative air humidity must be below 80%.
It is recommended to use paint from the same production batch to avoid differences in the shade of the finish coat.
Stir the paint thoroughly. Stirring should be done with a wide, flat slat or a construction mixer at low speeds, carefully, avoiding the formation of air bubbles, for 1–3 minutes. It is not recommended to mix the material by shaking the closed can. After transportation and/or active stirring, if air bubbles appear, the paint needs to settle until they disappear.
Apply the paint to the prepared dry clean surface with a brush, roller, or spray gun. For rough surfaces such as textured plasters, brick, concrete blocks, and relief ceilings, it is recommended to use rollers with a pile length of 12−25 mm. For
rough surfaces such as putties, plasters, and concrete — with a pile length of 8–12 mm. For smooth surfaces such as gypsum board, MDF, chipboard, and architectural decor elements (architraves, moldings, ceiling cornices) — with a pile length of up to 6 mm. The paint is ready for use; for
application by brush or roller, it can be diluted with water by no more than 5% if necessary. For airless spraying, dilution with water by 5–10% is allowed, nozzle size 0.013–0.015″, pressure 180–190 bar. The spray angle is chosen based on the area and geometric features of the surface being painted.

To obtain a rich color and improve the appearance of the surface, it is necessary to apply two coats of paint.
Avoid exposure to direct sunlight and high humidity conditions during work.
After completing the work, wash hands and tools thoroughly with warm water.

Work should be performed using personal protective equipment for hands, eyes, and respiratory tract. Use in well-ventilated areas.

Store and transport in tightly closed containers at temperatures between +5° and +35°C.
Five-fold freezing is allowed for a total duration of no more than 2 weeks at temperatures no lower than -40°C.
The bucket containing the product should be protected from excessive heating and storage under direct sunlight should be avoided.
Subject to storage conditions, the guaranteed shelf life in closed factory packaging is 24 months from the date of manufacture.
Product separation may occur during storage, which is easily eliminated by stirring.
Keep partially used product in tightly closed containers and use as soon as possible.
The product is fire- and explosion-proof and does not contain flammable components.