The product is manufactured until July 2026.

Purpose:
Paint for painting walls and ceilings indoors with normal and high humidity (kitchens, bathrooms, corridors, etc.).

Substrate type:

• Concrete, brick, fiberboard and particleboard, gypsum board, plastered, previously painted surfaces (but not glossy), wallpaper for painting

Application method:

• Brush
• Roller
• Spray gun

Consumption:
4−7 m²/kg

Gloss level:
Matte

Tinting:
The paint is available in two bases: A (white) and C (transparent). It can be tinted manually or by computer (machine) in RAL, NCS, and other color catalogs.

Composition:
Polymer dispersion, pigments, fillers, functional additives, water.

Color:

• Base A — white.
• Base C — transparent

Gloss level:
Matte

Consumption* per 1 coat on a smooth non-absorbent surface:
5−7 m²/kg

Consumption per 1 coat on an uneven absorbent surface:
4−6 m²/kg

Wet scrub resistance GOST 32300/ DIN EN 13300:
Class 3

Density:
Base A approx. 1.56 kg/l
Base C approx. 1.4 kg/l

Non-volatile matter content:
Base A not less than 55%
Base C not less than 55%

Diluent:
Water

Drying time**:
1 hour

Next coat can be applied after:
1.5 hours

Wash resistance:
Wet cleaning with non-abrasive detergents

Substrate temperature during application:
from +5 °C to +35 °C

Transportation temperature:
from +5 °C to +35 °C

* Material consumption depends on the quality of the substrate preparation, the application method, the tool used, the skill of the workers, and may differ from the specified values.

** at t (+20±2) °C and relative air humidity not more than (65±5) %. When the temperature decreases or humidity increases, the drying time may increase. At air temperatures below +15°C or relative air humidity above 65%, apply the next layer no earlier than 24 hours later.

The paint is intended for painting walls and ceilings indoors with normal and high humidity (kitchens, bathrooms, corridors, etc.)

The paint can be applied to concrete, brick, fiberboard and particle board, gypsum plasterboard, plastered, previously painted surfaces (but not glossy), and wallpaper for painting

Tinting and Color Solutions

The paint is produced in two bases, A and C, and can be tinted by computer (machine) method into RAL, NCS, and other color catalogs. Base A is intended for tinting into light and pastel shades, and can also be used as white paint; it is permissible to add up to 5% of tinting pastes by weight of the paint.
Base C is used only in tinted form and is intended for tinting into saturated shades; it is permissible to add up to 10% of tinting pastes by weight of the paint. When painting in bright colors using Base C, it is recommended to first apply a layer of Base A paint tinted in a similar shade. Manual tinting using water-based tinting pastes is possible.
The organization performing the tinting is responsible for the tinting result.

Color Reproduction Features

Depending on the application conditions and the texture of the surface being painted, actual color shades may differ slightly from those presented in the color catalog. Before use, it is necessary to perform a test application and check the dried coating for color compliance.
To avoid differences in shade, it is recommended to use a product from the same production batch on one visual plane (the batch number is indicated on each package) or pre-mix materials from different batches in a 1:1 ratio; the application technology must remain unchanged.

Surface Preparation

Surface preparation should be carried out in accordance with SP 71.13330.2017.
Clean the surface from dust and dirt. Remove unstable layers of old paint and whitewash from previously painted surfaces. Sand hard and firmly adhering glossy surfaces to a matte state, and remove sanding dust. Level irregularities, hollows, cracks, and chips with Bergauf UNI PASTA water-dispersion putty, then sand.
Surfaces previously covered with chalk or lime paints must be thoroughly cleaned until completely removed. Intensively absorbing surfaces should be pre-primed to increase coating reliability and reduce paint consumption.
It is recommended to use primers from the Praktik line (depending on the type of substrate).

Application Conditions

The surface to be painted must be dry and clean, the substrate temperature for work must be from +5°C, the room temperature during paint application from +5°C to +35°C, and relative air humidity below 80%.
It is recommended to use paint from the same production batch to avoid differences in the shade of the finish layer.

Material Preparation

Stir the paint thoroughly. Stirring should be done with a wide and flat slat or a construction mixer at low speeds, carefully, avoiding the formation of air bubbles, for 1–3 minutes. It is not recommended to mix the material by shaking the closed can. After transportation and/or active stirring, if air bubbles occur, the paint needs to settle until they disappear.

Application Technology

Apply the paint to the prepared dry clean surface with a brush, roller, or spray gun. For rough surfaces such as textured plasters, brick, concrete blocks, and relief ceilings, it is recommended to use rollers with a pile length of 12–25 mm. For coarse surfaces such as putties, plasters, concrete, glass fiber, and painting non-woven fabric — with a pile length of 8–12 mm. For smooth surfaces such as drywall, MDF, particle board, architectural decor elements (casings, moldings, ceiling cornices) — with a pile length of up to 6 mm.
The paint is ready for use; for application by brush or roller, it can be diluted with water by no more than 5% if necessary. For airless spraying, dilution with water by 5–10% is allowed, nozzle 0.013–0.015″, pressure 180–190 bar. The spray angle is chosen based on the area and geometric features of the surface being painted.
To obtain a saturated color and improve the appearance of the surface, two coats of paint must be applied.

Precautions

During work, avoid exposure to direct sunlight and high humidity conditions. Upon completion of work, wash hands and tools thoroughly with warm water.

Storage and Transportation Conditions

Store and transport in tightly closed containers at a temperature of at least +5°C and no more than +35°C. Five-fold freezing is allowed for a total duration of no more than 2 weeks at a temperature not lower than -40°C.
The bucket with the product should be protected from excessive heating and storage under direct sunlight should be avoided. Subject to the conditions, the guaranteed shelf life in closed factory packaging is 24 months from the date of manufacture.
During storage, product separation is possible, which is easily eliminated by stirring. Keep partially used product in a tightly closed container and use as soon as possible.

Safety

The product is fire and explosion-safe, and does not contain flammable components.