Purpose:
The paint is designed for painting ceilings and upper wall panels inside dry rooms. The matte structure of the paint masks minor surface imperfections of the ceiling. It provides high-quality uniform coverage, leaving no splashes or streaks. It is easy to apply, dries quickly, and has no sharp odor. Manual tinting is possible using water-based tinting pastes.
Creates a snow-white "breathable" coating.
Visually expands the space.
Reliably covers in 2 coats.

Color:
Super white

Substrate type:
The paint can be applied to new and previously water-dispersion painted drywall; plastered, puttied, concrete, brick, chipboard, fiberboard, fiberglass, and smooth non-woven wallpaper.
For interior work.

Application method:

• brush
• roller
• spray gun

Consumption:
8−11 m²/kg

Gloss level:
Deep matte

Tinting:
Manual tinting is possible using water-based tinting pastes.

Composition:
Polymer dispersion, pigments, fillers, functional additives, biocides, water.

Color:
Super white

Gloss level:
Deep matte

Consumption* per 1 coat on a smooth non-absorbent surface:
8−11 m^2/l

Density:
1.5−1.55 kg/l

Drying time "touch dry"**:
0.5 hours

Time for applying the next coat**:
1 hour**

Substrate temperature during application:
+5 °C to 35 °C


* Material consumption depends on the quality of preparation and the absorption capacity of the substrate, the application method, the tool used, the qualification of the workers and may differ from the specified values.
** At t (+20±2)°C and relative air humidity not exceeding (65±5)%. If the temperature decreases or humidity increases, the drying time may increase. At air temperatures below +15°C or relative air humidity above 65%, apply the next coat no earlier than after 24 hours.

Purpose and scope of application
The paint can be applied to new and previously water-dispersion painted drywall; plastered, puttied, concrete, brick, chipboard, fiberboard, fiberglass, and smooth non-woven wallpaper.
For interior work.
For manual and mechanized application.

Used in all types of buildings and structures (A, B, C).

Manual tinting is possible using water-based tinting pastes.

Substrate preparation
Substrate preparation should be carried out in accordance with SP 71.13330.2017.
Clean the substrate from dust and dirt. Remove unstable layers of old paint and whitewash from previously painted surfaces. Sand hard and firmly adhering glossy surfaces to a matte state, and remove the sanding dust. Level irregularities, depressions, cracks, and chips with Bergauf putty, then sand.
Surfaces previously covered with chalk or lime paints must be thoroughly cleaned until completely removed. Highly absorbent surfaces should be pre-primed with Praktik strengthening primer for painting to increase coating reliability and reduce paint consumption.

Work procedure
Mix the paint thoroughly. The paint is ready for use; if necessary, dilution with water of no more than 5% is possible. Apply the paint to a prepared dry clean surface with a roller, brush, or spray gun in two layers. For rough surfaces (textured plasters, brick, concrete blocks, relief ceilings), it is recommended to use rollers with a pile length of 12−25 mm. For coarse surfaces (putties, plasters, concrete) — with a pile length of 8−12 mm. For smooth surfaces (drywall, MDF, chipboard, architectural decor elements (architraves, moldings, ceiling cornices)) — with a pile length of up to 6 mm. For airless spraying, dilution with water by 5−10% is allowed, nozzle 0.013−0.015″, pressure 180−190 bar. During work, avoid exposure to direct sunlight, high humidity conditions, and atmospheric precipitation. Air and substrate temperature during application from +5°C to +35°C, relative air humidity below 80%.
Upon completion of work, wash hands and tools thoroughly with warm water.

Safety precautions
Work should be performed using personal protective equipment for hands, eyes, and respiratory tract. Use in well-ventilated areas. In case of contact with eyes, rinse immediately with water. In case of contact with skin, wash with soap and water.

Storage and transportation conditions
Store and transport in tightly closed containers at temperatures from +5°C to +35°C. Five-fold freezing for a total duration of no more than 2 weeks at a temperature not lower than -40°C is allowed. The product bucket should be protected from excessive heating and storage under direct sunlight should be avoided. Subject to storage conditions, the guaranteed shelf life in closed factory packaging is 24 months from the date of manufacture. During storage, product separation may occur, which is easily eliminated by stirring. Keep partially used product in a tightly closed container and use as soon as possible.
The product is fire and explosion-proof and does not contain flammable components.

Disposal
Do not pour paint products into sewers, water bodies, or onto the soil. Dispose of dry empty containers in accordance with local legislation; transfer liquid residues to hazardous waste collection points.